YouTube Jog Dial

Info

Getting tired of always losing my place when I am watching a tutorial and have to tab out to pause or rewind. So I put together a USB knob that will allow me to Pause/Play Rewind Fast Forward youtube videos, without me losing my place

Part List

• trinket
• rotary encoder
• knob

Code

#include "TrinketHidCombo.h"
 
#define PIN_ENCODER_A 0
#define PIN_ENCODER_B 2
#define TRINKET_PINx  PINB
#define PIN_ENCODER_SWITCH 1
 
static uint8_t enc_prev_pos   = 0;
static uint8_t enc_flags      = 0;
static char    sw_was_pressed = 0;
 
void setup()
{
  // set pins as input with internal pull-up resistors enabled
  pinMode(PIN_ENCODER_A, INPUT);
  pinMode(PIN_ENCODER_B, INPUT);
  digitalWrite(PIN_ENCODER_A, HIGH);
  digitalWrite(PIN_ENCODER_B, HIGH);
 
  pinMode(PIN_ENCODER_SWITCH, INPUT);
  // the switch is active-high, not active-low
  // since it shares the pin with Trinket's built-in LED
  // the LED acts as a pull-down resistor
  digitalWrite(PIN_ENCODER_SWITCH, LOW);
 
  TrinketHidCombo.begin(); // start the USB device engine and enumerate
 
  // get an initial reading on the encoder pins
  if (digitalRead(PIN_ENCODER_A) == LOW) {
    enc_prev_pos |= (1 << 0);
  }
  if (digitalRead(PIN_ENCODER_B) == LOW) {
    enc_prev_pos |= (1 << 1);
  }
}
 
void loop()
{
  int8_t enc_action = 0; // 1 or -1 if moved, sign is direction
 
  // note: for better performance, the code will now use
  // direct port access techniques
  // http://www.arduino.cc/en/Reference/PortManipulation
  uint8_t enc_cur_pos = 0;
  // read in the encoder state first
  if (bit_is_clear(TRINKET_PINx, PIN_ENCODER_A)) {
    enc_cur_pos |= (1 << 0);
  }
  if (bit_is_clear(TRINKET_PINx, PIN_ENCODER_B)) {
    enc_cur_pos |= (1 << 1);
  }
 
  // if any rotation at all
  if (enc_cur_pos != enc_prev_pos)
  {
    if (enc_prev_pos == 0x00)
    {
      // this is the first edge
      if (enc_cur_pos == 0x01) {
        enc_flags |= (1 << 0);
      }
      else if (enc_cur_pos == 0x02) {
        enc_flags |= (1 << 1);
      }
    }
 
    if (enc_cur_pos == 0x03)
    {
      // this is when the encoder is in the middle of a "step"
      enc_flags |= (1 << 4);
    }
    else if (enc_cur_pos == 0x00)
    {
      // this is the final edge
      if (enc_prev_pos == 0x02) {
        enc_flags |= (1 << 2);
      }
      else if (enc_prev_pos == 0x01) {
        enc_flags |= (1 << 3);
      }
 
      // check the first and last edge
      // or maybe one edge is missing, if missing then require the middle state
      // this will reject bounces and false movements
      if (bit_is_set(enc_flags, 0) && (bit_is_set(enc_flags, 2) || bit_is_set(enc_flags, 4))) {
        enc_action = 1;
      }
      else if (bit_is_set(enc_flags, 2) && (bit_is_set(enc_flags, 0) || bit_is_set(enc_flags, 4))) {
        enc_action = 1;
      }
      else if (bit_is_set(enc_flags, 1) && (bit_is_set(enc_flags, 3) || bit_is_set(enc_flags, 4))) {
        enc_action = -1;
      }
      else if (bit_is_set(enc_flags, 3) && (bit_is_set(enc_flags, 1) || bit_is_set(enc_flags, 4))) {
        enc_action = -1;
      }
 
      enc_flags = 0; // reset for next time
    }
  }
 
  enc_prev_pos = enc_cur_pos;
 
  if (enc_action > 0) {
  //Fast Forward  youtube hotkey (l)
     TrinketHidCombo.pressKey(0, 15);
     TrinketHidCombo.pressKey(0, 0);
  }
  else if (enc_action < 0) {
    //Rewind youtube hotkey (j)
    TrinketHidCombo.pressKey(0, 13);
     TrinketHidCombo.pressKey(0, 0);
  }
 
  // remember that the switch is active-high
  if (bit_is_set(TRINKET_PINx, PIN_ENCODER_SWITCH)) 
  {
    if (sw_was_pressed == 0) // only on initial press, so the keystroke is not repeated while the button is held down
    {
     //PlayPause youtube hotkey (k)
     TrinketHidCombo.pressKey(0, 14);
     TrinketHidCombo.pressKey(0, 0); 
     
     delay(5); // debounce delay
    }
    sw_was_pressed = 1;
  }
  else
  {
    if (sw_was_pressed != 0) {
      delay(5); // debounce delay
    }
    sw_was_pressed = 0;
  }
 
  TrinketHidCombo.poll(); // check if USB needs anything done
}